Sry if in wrong discussion I was in the middle of renaming a Point and being a noob I did not have the rename up So as I was renaming it I hot keyed something not sure what But now I cannot see nor rename any points that are placed. They will appear in the left hand box but I cannot rename them and it is really frustrating How do i fix this.
Actions
Unit Group - Pick each unit in (Any units in (Entire map) owned by player Any
Player matching Excluded: Missile, Dead, Hidden, with at most Any Amount) and do (Actions)
I have been into Units Unit Groups unit selection. I can find the Units in units group for Player Which gives me the Unit Group- Pick each unit in (**) How ever I can not for the life of me figure out how to get "Any Units" in(entire map) owned by player any. I am trying to get my water to damage the units with out a timer sence it is set to Rise and fall via a point that trigger works fine I just cant seem to figure out the unit Group any statement Please help
Ok Trigger works for Players but not the A.I cant figure out what needs to go in after to re initiate there attack or even get them to go to the trigger area. The trigger is set up as a portal area that will drop you down to a lower region on the map Players can click on it and will be sent down with out an issue and can use the return pad at the lower end to get back to the top the Trigger code set is as follows.
Event:
Unit - Any unit enters (Region) out 1-2
Actions Unit- Move triggering Unit Instantly to (Point) Drop Point 1-2
Unit- Order Triggering Unit to Stop (Replace existing orders)
I had to put the stop command in to stop the units from running back to the return pad I have tried moving my region out a bit but they always want to run back up even the users units were doing this. However the A.I will scout around the Out region but never go on it and if it does they will stand at the Lower drop point and not do anything. How do I get the A.I to go to the Out region as well as re initiate there attack sequence.
Ok Trigger works for Players but not the A.I cant figure out what needs to go in after to re initiate there attack or even get them to go to the trigger area. The trigger is set up as a portal area that will drop you down to a lower region on the map Players can click on it and will be sent down with out an issue and can use the return pad at the lower end to get back to the top the Trigger code set is as follows.
Event:
Unit - Any unit enters (Region) out 1-2
Actions Unit- Move triggering Unit Instantly to (Point) Drop Point 1-2
Unit- Order Triggering Unit to Stop (Replace existing orders)
I had to put the stop command in to stop the units from running back to the return pad I have tried moving my region out a bit but they always want to run back up even the users units were doing this. However the A.I will scout around the Out region but never go on it and if it does they will stand at the Lower drop point and not do anything. How do I get the A.I to go to the Out region as well as re initiate there attack sequence.
0
0
Sry if in wrong discussion I was in the middle of renaming a Point and being a noob I did not have the rename up So as I was renaming it I hot keyed something not sure what But now I cannot see nor rename any points that are placed. They will appear in the left hand box but I cannot rename them and it is really frustrating How do i fix this.
0
@BasharTeg: Go
Thank you Was searching web for hours trying to figure it out did not think to use that one sense I had no Actual region boxes placed
0
Actions Unit Group - Pick each unit in (Any units in (Entire map) owned by player Any Player matching Excluded: Missile, Dead, Hidden, with at most Any Amount) and do (Actions)
I have been into Units Unit Groups unit selection. I can find the Units in units group for Player Which gives me the Unit Group- Pick each unit in (**) How ever I can not for the life of me figure out how to get "Any Units" in(entire map) owned by player any. I am trying to get my water to damage the units with out a timer sence it is set to Rise and fall via a point that trigger works fine I just cant seem to figure out the unit Group any statement Please help
0
Ok Trigger works for Players but not the A.I cant figure out what needs to go in after to re initiate there attack or even get them to go to the trigger area. The trigger is set up as a portal area that will drop you down to a lower region on the map Players can click on it and will be sent down with out an issue and can use the return pad at the lower end to get back to the top the Trigger code set is as follows.
Event: Unit - Any unit enters (Region) out 1-2
Actions Unit- Move triggering Unit Instantly to (Point) Drop Point 1-2 Unit- Order Triggering Unit to Stop (Replace existing orders)
I had to put the stop command in to stop the units from running back to the return pad I have tried moving my region out a bit but they always want to run back up even the users units were doing this. However the A.I will scout around the Out region but never go on it and if it does they will stand at the Lower drop point and not do anything. How do I get the A.I to go to the Out region as well as re initiate there attack sequence.
0
Ok Trigger works for Players but not the A.I cant figure out what needs to go in after to re initiate there attack or even get them to go to the trigger area. The trigger is set up as a portal area that will drop you down to a lower region on the map Players can click on it and will be sent down with out an issue and can use the return pad at the lower end to get back to the top the Trigger code set is as follows.
Event: Unit - Any unit enters (Region) out 1-2
Actions Unit- Move triggering Unit Instantly to (Point) Drop Point 1-2 Unit- Order Triggering Unit to Stop (Replace existing orders)
I had to put the stop command in to stop the units from running back to the return pad I have tried moving my region out a bit but they always want to run back up even the users units were doing this. However the A.I will scout around the Out region but never go on it and if it does they will stand at the Lower drop point and not do anything. How do I get the A.I to go to the Out region as well as re initiate there attack sequence.